CPR Call Blocker Protect+ Programming Codes

CPR Call Blocker Protect+ Programming Codes

IMPORTANT - WHEN PROGRAMMING THE CALL BLOCKER PROTECT +
YOU WILL ALWAYS HEAR THE BT OPERATOR SAYING YOUR CALL CANNOT
BE COMPLETED AS DIALLED. THIS IS NORMAL WITH THE PROTECT + AS
THE LINE IS LEFT OPEN FOR MANUAL PROGRAMMING OUR END IF NEEDED.
SIMPLY IGNORE THE OPERATOR AND JUST LISTEN FOR THE CONFIRMATION
BEEPS AFTER THE # KEYS. THE NUMBERS AND CODES WILL THEN GO
THROUGH WITHOUT ISSUES.

Whitelist (Allow a number): * * 8 # (beep) NUMBER # (beep)

Blacklist (Remove that number): * * 6 # (beep) NUMBER # (beep)


1. To Turn On: Get a dial tone and input * * 4 # (beep) * 4 # (beep) - Call Blocker Protect + is already turned ON by default (Everything Blacklisted)

2. To Turn Off: Get a dial tone and input * * 3 # (beep) * 3 # (beep) - Turning OFF Call Blocker Protect + will allow ALL numbers through (Everything Whitelisted) 

You will hear a ‘beep’ after each # to confirm success.


Allowing or Blocking all “Withheld / Private” Callers


1. To Whitelist: Get a dial tone and input * * 8 # (beep) 7 * # (beep)


2. To Blacklist: Get a dial tone and input * * 6 # (beep) 7 * # (beep)


You will hear a ‘beep’ after each # to confirm success.


Allowing or Blocking all “Unavailable / Unknown” Callers


1. To Whitelist: Get a dial tone and input * * 8 # (beep) # (beep)


2. To Blacklist: Get a dial tone and input * * 6 # (beep) # (beep)


You will hear a ‘beep’ after each # to confirm success.



PROGRAMMING CODES



Allowing or Blocking all “Out of Area / International” Callers


1. To Whitelist: Get a dial tone and input * * 8 # (beep) * # (beep)


2. To Blacklist: Get a dial tone and input * * 6 # (beep) * # (beep)


You will hear a ‘beep’ after each # to confirm success.


Allowing or Blocking all VOIP / I.P Rogue Diallers 


1. To Whitelist: Get a dial tone and input * * 8 # (beep) 6 * # (beep)


2. To Blacklist: Get a dial tone and input * * 6 # (beep) 6 * # (beep)


You will hear a ‘beep’ after each # to confirm success.


Allowing or Blocking all “0” type calls (Single digit spoof callers) 


1. To Whitelist: Get a dial tone and input * * 8 # (beep) 0 # (beep)


2. To Blacklist: Get a dial tone and input * * 6 # (beep) 0 # (beep)


You will hear a ‘beep’ after each # to confirm success.


Resetting the Call Blocker back to factory settings


1. Get a dial tone and input * * 1 # (beep) * 1 # (beep)

    • Related Articles

    • ABOUT the CPR Call Blocker Protect+

      This is the CPR Call Blocker Protect + model.  This Call Blocker has been designed by us at CPR specifically for the elderly or very vulnerable. These Call Blockers are designed to BLOCK EVERY call that comes through to a customer's line, unless they ...
    • CPR Call Blocker APP for Android

        Adding Contacts to the Blocklist ✎   Upon starting the app your blocklist will be blank by default. There are a variety of ways to add a number to the blocklist,  accessible via the ‘+ ADD‘ button above the  ‘ Blocklist‘ tab icon. You can choose ...
    • NEW V10,000 + V5000 Quick Programming Codes

      V10,000 Quick Programming Codes Change Mode: 1. Get a dial tone 2. Hold CALL LIST for 5 seconds until the call blocker beeps this will change the call blocker to mode “100” 3. Hang up and repeat the process for mode “200” and “300” Turn ON Blocking ...
    • ABOUT CPR Call Blocker Protect +

      This is the CPR Call Blocker Protect + model.  This Call Blocker has been designed by us at CPR for the elderly or very vulnerable.  These Call Blockers are designed to BLOCK EVERY call that comes through to a customer's line, unless they are ...
    • ABOUT CPR Call Blocker v103

      This is the CPR Call Blocker v.103 model.  This unit is basically the same as the previous models, but has newer programming codes inputted to block even more anonymous cold callers.  It has 200 updated pre-programmed numbers of the worse known ...